3-in-1 Nutrition Centre SCF280 3 a 1 B C h D E F i J k l g M n o P EngliSh 6 1 Cestina 18 eesti Hrvatski 30 Magyar 36 Lietuviskai 8 Latviesu 5 PolSki 60 român 66 7 SlovEnSky 79 sLovensCina 85 SrPSki 91 97 SCF280 6 EngliSh introduction Philips is dedicated to producing caring and reliable products that new mothers and fathers really need - products whose reliability and operating quality create confidence. This Philips 3-in-1 Nutrition Centre is a steriliser, a bottle warmer and a food steamer all in one. It enables you to safely and quickly heat baby bottles and jars of baby food, to keep them warm, to disinfect baby bottles and small objects and to steam all kinds of vegetables and fruit. The unique design fits all baby bottles and jars of baby food, while the temperature control system ensures the highest safety standards. Philips Baby Care: taking care together important Read these instructions for use carefully before using the appliance and save them for future reference. , Check if the voltage that is indicated on the appliance corresponds to the local mains voltage before you connect the appliance. , This appliance is suitable for mains voltages from 0 to 0 volts. , If the mains cord is damaged, it must be replaced by Philips, a service centre authorised by Philips or similarly qualified persons in order to avoid a hazard. , Do not expose the appliance to extreme heat or direct sunlight. , Never disassemble the base to avoid the risk of electric shock. , Never use the base without water in it. , Only use pure tap water without any additives. , Do not put bleach, descaling agents or other chemicals in the appliance. , Do not immerse the base, the mains cord or the mains plug in water or any other liquid. , Always let the appliance cool down before moving or storing it. , The appliance becomes extremely hot when it is in use and may cause burns if it is touched. Always lift the lid, the cap and the cover by their handle. , Beware of hot steam that comes out of the vent in the cover when the appliance is in use without the cap. Steam can cause burns. , Never move or open the appliance when it is in use or when the water in it is still hot. , Always place and use the appliance on a dry, stable, level and horizontal surface. , Do not place the appliance on a hot surface or in a heated oven. , Keep the appliance out of the reach of children. , Do not let the mains cord hang over the edge of the table or worktop on which the appliance stands. , Only use baby bottles that have been approved for boiling. , Use and store the appliance at a temperature between 10°C and 35°C. , Always pour any remaining water out of the appliance after use. , Test food on the back of your hand before serving it, to ensure that it is at a safe temperature for your baby. , Always unplug the appliance after use. , Never place items on top of the appliance when it is in use. general description (Fig. 1) Steriliser lid Basket Container Protective grid Water reservoir Mains cord Control knob A B C D E F G EngliSh H I J K L M N O P Measuring cup Base with heating element Indicator LED Cord storage brackets Cap Cover Cover handle Steaming bowl Base with heating element Preparing for use 1 Place the Nutrition Centre on a dry, stable, level and horizontal surface out of the reach of children. Unwind the required length of mains cord from the cord storage brackets in the base. 3 Insert the mains plug into the wall socket. , The indicator LED starts to burn green. The Nutrition Centre is now in standby mode. The appliance does not heat up until you press and turn the control knob to select a setting. using the appliance temperature overview , - 7 Babies like their milk and food to be at a temperature of 37°C. The control knob enables you to set the correct food temperature. The setting depends on the amount, consistency and current temperature of the milk or food. (Fig. ) y refrigerator temperature (approx. 10°C.) . room temperature (approx. 20°C.) m bottle contents up to 200ml , minimum bottle contents approx. 60ml Note:If all the water has evaporated before the heating process is completed, the 3-in-1 Nutrition Centre starts to beep and the indicator LED starts to blink red. If this happens, press the control knob to interrupt the heating process and fill the water reservoir. heating heating baby bottles 1 Pour 0ml water into the water reservoir with the measuring cup. (Fig. 3) Remove the cap from the cover (1) and place the cover on the base (). Place the bottle on the protective grid in the base (3). (Fig. ) 3 Look up the desired setting in the temperature overview. The setting depends on the amount of milk in the bottle and the current bottle temperature. Press (1) and turn () the control knob to the desired setting. (Fig. 5) , The indicator LED starts to burn red continuously and you hear a beep to indicate that the heating process has started. , The heating process takes up to about 5 minutes, depending on the quantity and the temperature of the milk. , When the milk has reached the right temperature, you hear three beeps. The indicator LED blinks red three times and then turns green. 5 Take the bottle out of the appliance and unplug the appliance. 8 EngliSh Note:Always test the milk on the back of your hand first to ensure it has a safe temperature for your baby. heating jars of baby food 1 Pour 0ml water into the water reservoir with the measuring cup. (Fig. 3) Place the jar (max. content 150g) on the protective grid in the base. Place the cover on the base. (Fig. 6) 3 Press (1) and turn () the control knob to n. (Fig. 5) , The indicator LED starts to burn red continuously and you hear a beep to indicate that the heating process has started. , The heating process takes about 5 minutes, depending on the quantity, type and temperature of the food. , When the food has reached the right temperature, you hear three beeps. The indicator LED blinks red three times and then turns green. Remove the cover from the base, remove the jar and unplug the appliance. Tip:To distribute the heat better, stir the contents of the jar after heating it. Note:Always check if the contents of the jar are at the correct temperature by testing some of the food on the back of your hand. keeping bottles and jars warm You can also use the 3-in-1 Nutrition Centre to keep bottles and jars warm for a short time. After the heating process is finished, simply leave the bottle or jar on the protective grid in the base and leave the cover on the base. The cover retains the heat and keeps the bottle or jar warm for some time. For microbiological and hygienic reasons, you must never keep baby food warm for more than one hour. Sterilising With the container, you can use the 3-in-1 Nutrition Centre to sterilise bottles and small objects like rubber teats and small toys. The Nutrition Centre disinfects the objects completely by destroying all harmful bacteria. Note:This appliance does not sterilise according to clinical standards. Note:Before you sterilise bottles and objects, clean them first. 1 Pour 50ml water into the water reservoir with the measuring cup. (Fig. 3) Place the container on the base. 3 Place the bottles upside down in the container. (Fig. 7) The container can contain four wide-neck bottles or six regular-sized bottles. Snap the bottle necks onto the projections at the bottom of the container. 5 Place small objects in the basket and place the basket in the container. Place the lid on the container. (Fig. 8) 6 Press and turn the control knob to /. (Fig. 5) , The indicator LED starts to burn red continuously and you hear a beep to indicate that the sterilising process has started. , After about 15 minutes, you hear three beeps. The indicator LED blinks red three times and then turns green to indicate that the stelising process has finished. 7 Remove the bottles and objects from the container and unplug the appliance. EngliSh Steaming 9 Certain vegetables and fruit are perfect for babies aged 4 months or older if they are gently steamed. Steaming is the most healthy way of preparing food. It preserves lots of vitamins and other healthy nutrients. The 3-in-1 Nutrition Centre steams 50g to 150g of hard or soft vegetables and fruit. The time that is needed to steam the food depends on the quantity, type and temperature of the food. 1 Pour 00ml water into the water reservoir with the measuring cup. (Fig. 3) Cut the vegetables or fruit into small pieces and place them in the steaming bowl. Place the steaming bowl on the base and put the cover on the steaming bowl. (Fig. 9) 3 Press and turn the control knob to the desired steaming time: 15, 0, 5 or 30 minutes. (Fig. 5) , The indicator LED blinks red and you hear a beep to indicate that the steaming process has started. , When the set steaming time has elapsed, you hear three beeps. The indicator LED blinks green. , Remove the cover from the steaming bowl and check the food. , If it is not properly steamed, check if there is still enough water in the base. If not, add more water. Then select a new steaming time to switch on the appliance again. When the food is ready, take the steaming bowl off the base and unplug the appliance. Defrosting 1 Pour 00ml water into the water reservoir with the measuring cup. (Fig. 3) Put the frozen food in the steaming bowl and place the cover on the steaming bowl. (Fig. 10) 3 Press and turn the control knob to the desired steaming time: 15, 0, 5 or 30 minutes. (Fig. 5) , The indicator LED blinks red and you hear a beep to indicate that the steaming process has started. , When the set steaming time has elapsed, you hear three beeps and the indicator LED blinks green. , Remove the cover and check whether the food is defrosted. , If it is not, check if there is still enough water in the base. If not, add more water. Then select a new steaming time to switch on the appliance again. When the food is defrosted, remove the cover from the steaming bowl, take the steaming bowl off the base, and unplug the appliance. Cleaning Do not use abrasive or aggressive cleaning agents (e.g. bleach) to clean this appliance. Note:All parts of the 3-in-1 Nutrition Centre except the base are dishwasher-proof. 1 Always unplug the appliance and let it cool down before you clean it. Clean the base with a moist cloth. 3 Clean the other parts in the dishwasher or in hot water with some washing-up liquid. Descaling Descale the base, the container and the steaming bowl when scale becomes visible. 10 EngliSh 1 Pour a solution of 1 part white vinegar (8% acetic acid) and parts water (about 60ml in total) into the base. Place the container with lid or steaming bowl with cover and cap on the base. 3 Press and turn the control knob to / . , The indicator LED starts to burn red continuously and you hear a beep to indicate that the process has started. , After about 15 minutes, you hear three beeps. The indicator LED blinks red three times and then turns green to indicate that the process has finished. Rinse the bowl, the container and/or the steaming bowl and wipe them with a damp cloth. , If not all scale has disappeared, repeat the above steps. environment , Do not throw away the appliance with the normal household waste at the end of its life, but hand it in at an official collection point for recycling. By doing this, you help to preserve the environment. (Fig. 11) Guarantee & service If you need information or if you have a problem, please visit the Philips website at www.philips.com or contact the Philips Customer Care Centre in your country (you find its phone number in the worldwide guarantee leaflet). If there is no Customer Care Centre in your country, turn to your local Philips dealer or contact the Service Department of Philips Domestic Appliances and PersonalCare BV. EngliSh 11 Frequently asked questions This chapter lists the questions most frequently asked about the appliance. If you cannot find the answer to your question, contact the Customer Care Centre in your country. Question Why does the indicator LED not burn? Answer Check whether you have inserted the plug into a wall socket properly. Perhaps you try to run the appliance at the wrong voltage. This appliance operates at mains voltages between 220 and 240 volts Why does the indicator LED blink red while the appliance beeps? Why does the base overflow? Why is the temperature of the milk too low after heating up? Press the control knob to interrupt the process and check the water level in the base. Refill the base if necessary. You have poured too much water into the base. Stick to the quantities mentioned in the temperature overview. You have selected a too low setting for the quantity of milk you want to warm. Switch on the appliance briefly again to warm the milk to the required temperature. Select a higher setting next time. You have selected a too high setting for the quantity of milk you want to warm or you left the bottle in t ...